2019 Range Rover

НАСТРОЙКИ КРУИЗ-КОНТРОЛЯ ДЛЯ СЛОЖНЫХ ДОРОЖНЫХ УСЛОВИЙ ALL TERRAIN PROGRESS CONTROL (ATPC)

NOTES

When the vehicle is stationary, press and hold the brake pedal to maintain control of the vehicle while using the SET+ button.

NOTES

Light and gentle application of the accelerator pedal temporarily overrides the current set speed. Release the accelerator pedal to revert the All Terrain Progress Control (ATPC) system back to the previously selected set speed.

NOTES

Selecting very low speeds when pulling away on slippery surfaces can affect the vehicle's ability to make progress. For improved pulling away performance, it is recommended to select a set speed that is sufficient to maintain the vehicle's progress.

NOTES

Light and gentle application of the brake pedal lowers the set speed. When the brake pedal is fully released, the ATPC system maintains the speed at which the vehicle was travelling when the brake pedal was released. If the brake pedal is pressed when the ATPC system is active, a slight pulsation movement may be felt through the brake pedal.

When the ATPC system is enabled, the desired set speed for the vehicle can be set and adjusted. Use the controls mounted on the right side of the steering wheel.

  1. SET+ button: Press once to enable the ATPC system to recognise that the desired set speed is to be set and adjusted. Press repeatedly, or press and hold, to increase the set speed, up to a maximum speed of 30 km/h (19 mph). Alternatively, when driving, press the SET+ button for the vehicle's current speed to be the set speed. The instrument panel displays the current set speed.

  2. RESUME button: Press to resume the set speed if the vehicle's speed has been lowered via gentle application of the brake pedal.

    WARNING

    RESUME should only be used if the driver is aware of the set speed and intends to return to it. Inappropriate use can potentially lead to vehicle damage or personal injury.

  3. - button: Press and release repeatedly, or press and hold, to decrease the desired set speed. The minimum feature speed is 3.5 km/h (2.2 mph) in high range or 1.8 km/h (1.1 mph) in low range. See ВЫБОР ПОВЫШЕННОГО И ПОНИЖЕННОГО ДИАПАЗОНА.

  4. CANCEL button: Press to exit full function mode and revert the ATPC system to descent control mode. See ИСПОЛЬЗОВАНИЕ КРУИЗ-КОНТРОЛЯ ДЛЯ СЛОЖНЫХ ДОРОЖНЫХ УСЛОВИЙ ALL TERRAIN PROGRESS CONTROL (ATPC).

    NOTES

    Pressing the CANCEL button retains the set speed for future use, unless the ATPC system or the ignition system is switched off.

The incremental increases or decreases of the set speed are influenced by the current set speed:

  • 0.5 km/h (0.3 mph) increments if the set speed is between 0 and 5 km/h (0 and 3 mph).

  • 1 km/h (0.6 mph) increments if the set speed is between 5 and 10 km/h (3 and 6 mph).

  • 2 km/h (1.2 mph) increments if the set speed is between 10 and 30 km/h (6 and 19 mph).

When the vehicle is travelling at speeds between 30 km/h (19 mph) and 80 km/h (50 mph), the ATPC system operation is suspended. In this event, the ATPC warning lamp flashes. The ATPC system operation resumes when the vehicle's speed is less than 30 km/h (19 mph). If the vehicle’s speed exceeds 80 km/h (50 mph), the ATPC system disables. The ATPC warning lamp extinguishes. If required, the ATPC system has to be switched on again. See КРУИЗ-КОНТРОЛЬ НА НИЗКИХ СКОРОСТЯХ ПРИ ДВИЖЕНИИ НА РАЗЛИЧНЫХ ТИПАХ ПОВЕРХНОСТИ (ATPC) (ЯНТАРНЫЙ).