2019 Range Rover


Make sure the following warnings have been read and fully understood before driving the vehicle. Failure to do so may result in an accident, leading to serious injury or death.


All tyre pressures, including the spare, should be checked regularly using an accurate tyre pressure gauge, when the tyres are cold. Failure to properly maintain the tyre pressures could increase the risk of tyre failure, resulting in the loss of vehicle control and potential personal injury or death.


Pressure checks should be carried out only when the tyres are cold, and the vehicle has been stationary for more than 3 hours. A hot tyre at, or below, the recommended cold inflation pressure, is dangerously under-inflated.


Never drive the vehicle if the tyre pressures are incorrect. Under-inflation causes excessive flexing and uneven tyre wear, which can lead to sudden tyre failure. Over-inflation causes harsh ride, uneven tyre wear and poor handling.


Do not drive the vehicle with a leaking tyre. Even if the tyre appears to be inflated, it could be dangerously under-inflated and will continue to deflate. Replace the tyre or contact an approved repairer.


Under-inflation also reduces fuel efficiency and tyre tread life and may affect the vehicle’s handling and stopping ability.


If the vehicle has been parked in strong sunlight, or used in high ambient temperatures, do not reduce the tyre pressures. Move the vehicle into the shade and allow the tyres to cool before rechecking the pressures. Failure to properly maintain the tyre pressures could increase the risk of tyre failure, resulting in personal injury or death.

The recommended tyre pressures for all conditions are listed on a label located at the base of the driver’s door opening.

  1. Tyre information label on the driver's side.

  2. Light load information.

  3. Heavy load information.


The vehicle’s actual tyre pressures and recommended inflation pressures for current ambient conditions may also be shown. See ПРОВЕРКА ДАВЛЕНИЯ В ШИНАХ.


The instrument panel can display recommended cold inflation pressures. See ПОИСК СВЕДЕНИЙ О РЕКОМЕНДОВАННОМ ДАВЛЕНИИ В ШИНАХ.

Check the tyres, including the spare, for condition and pressure on a weekly basis and before long journeys.

If the tyre pressures are checked while the vehicle is inside a protected, covered area, e.g., a garage, and subsequently driven in lower outdoor temperatures, tyre under-inflation could occur.

A slight pressure loss occurs naturally with time. If this exceeds 0.14 bar (2 psi, 14 kPa) per week, have the cause investigated and rectified by qualified personnel.

If it is necessary to check the tyre pressures when the tyres are warm, expect the pressures to have increased by up to 0.3 to 0.4 bar (4 to 6 psi, 30 to 40 kPa). Do not reduce the tyre pressures to the cold inflation pressure under these circumstances. Allow the tyres to cool fully before adjusting the pressures.

For vehicles with a Tyre Pressure Monitoring System (TPMS) it is possible to adjust the pressure of a warm tyre, providing the warm inflation pressures are used. See ПРОВЕРКА ДАВЛЕНИЯ В ШИНАХ.


Not all vehicles have a TPMS fitted.

The following procedure should be used to check and adjust the tyre pressures:


The loading of the vehicle should always be considered when checking and adjusting tyre pressures.

  1. Remove the valve cap.

  2. Firmly attach a tyre pressure gauge and/or inflator to the valve.


    To avoid damaging the valves, do not apply excessive force or sideways force on the gauge and/or inflator.


    To avoid damage to the TPMS valves, it is recommended not to use rigid tyre inflation wands. Using rigid tyre inflation wands could result in excess leverage and sideways pressure on the valve.

  3. Read the tyre pressure from the gauge and add air, if required.

  4. If air is added to the tyre, remove the gauge and re-attach it before reading the pressure. Failure to do so, may result in an inaccurate reading.

  5. If the tyre pressure is too high, remove the gauge and press the centre of the valve to allow air out of the tyre. Refit the gauge to the valve and check the pressure.

  6. Repeat the process, adding or removing air as required, until the correct tyre pressure is reached.

  7. Refit the valve cap.


The full size spare tyre's pressure should always be maintained at the maximum pressure for heavy/full load conditions, as stated on the tyre placard label. Failure to comply with the maximum pressure for heavy/full load conditions activates the TPMS warning lamp for the spare wheel and tyre assembly. Similarly, a stored, punctured wheel and tyre assembly activate the TPMS warning lamp until the puncture is repaired and the tyre is correctly inflated. See СИСТЕМА КОНТРОЛЯ ДАВЛЕНИЯ В ШИНАХ (TPMS).